LOT 1A

BP07-A

BP08-A

BP08-B

PBP09-A

PBP09-B

3/4 PLATE - 3/4 AB - 3" REQD. PROJECTION

1/2 PLATE - 3/4 AB - 3" REQD. PROJECTION

1/2 PLATE - 3/4 AB - 3" REQD. PROJECTION

1/2 PLATE - 3/4 AB - 3" REQD. PROJECTION

1/2 PLATE - 3/4 AB - 3" REQD. PROJECTION

8"

11 7/8"

1 1/2"

1 1/2"

STEEL LINE

11 7/8"

2" 10" 2"

2" 10" 2"

01/10/2022 06:39:12am

5"

1 1/2" 1 1/2"

1 1/2" 1 1/2" 5"

5" 5"

5" 5"

8"

8"

3 1/2" 3" 5 9/16"

1'-2"

1'-2"

STEEL LINE

6 1/4" 3 1/2" 3" 5 3/8"

1'-0 1/16"

(972) 524-5407

(972) 524-5417 FAX:

6 1/4" 3 1/2" 3" 5 3/8"

9 3/4"

2" 2"

2" 2"

9 3/4"

PHONE:

8"

STEEL LINE

8"

PBP09-C

PBP09-D

BP10-A

A

1/2 PLATE - 3/4 AB - 3" REQD. PROJECTION

1/2 PLATE - 3/4 AB - 3" REQD. PROJECTION

3/4 PLATE - 3/4 AB - 3" REQD. PROJECTION

2"

2"

1'-0"

STEEL LINE

8"

STEEL LINE

*

*

CLR. OPENING

VARIES

5"

1 1/2" 1 1/2"

(2 3/4"-3 5/8")

STEEL LINE

8"

5 3/8" 3"

3 1/2"

(USE (2) 1/2" DIA EXPANSION RODS PER COLUMN)

BASE PLATE DETAILS DRAWING TITLE

8 1/8"

GIRT DEPTH + 2"

5 1/2" 3"

3 1/2"

1 1/2" 1 1/2"

3 1/8" 3" 2"

PROJECT NAME EMS - Phase II

1 1/2"

1 1/2"

5"

11 1/2"

3/4"

(RECOMMENDED) SECTION A

STEEL LINE

4

OHDFO

11 7/8"

4060 T.B. Herndon Avenue COLUMN BASE PLATES, EXCEPT 1/2 INCH DIAMETER ANCHOR RODS LOCATED AT DOORS WHICH SHALL ALL ANCHOR RODS SHALL HAVE A 3 INCH PROJECTION (UNLESS NOTED) ABOVE THE BOTTOM OF THE ERECTION NOTE!!! 2. BOTTOM OF BASE PLATE (B.O.B.P.) = 100'-0" EXCEPT AS NOTED. 1. FINISHED FLOOR ELEVATION = 100'-0" ERECTION NOTE!!!

STEEL LINE

FRAMED OPENING TYPICAL OVERHEAD DOOR

CUSTOMER NAME SIENNA CONSTRUCTION Baton Rouge, LA 70807 PROJECTING THREADS SHOULD BE GREASED OR OTHERWISE PROTECTED FROM CORROSION. DOUBLE NUTS, PLATE WASHERS, LEVELING PLATES, ETC., THAT MAY BE SPECIFIED BY OTHERS. ADDITIONAL PROJECTION LENGTH MUST BE CONSIDERED AND PROVIDED FOR ITEMS SUCH AS GROUT, ANCHOR BOLT MUST BE FLUSH WITH OR ABOVE THE TOP OF THE NUT. ONE 3/16 INCH WASHER, AND ONE HEAVY HEX NUT. IN THE INSTALLED POSITION, THE TOP OF THE THE PROJECTIONS SPECIFIED PROVIDE FOR A SINGLE BASE PLATE THICKNESS, AND APPLICATION OF ALL ANCHOR RODS SHALL HAVE A MINIMUM THREAD LENGTH OF 1/4 INCH LESS THAN THE PROJECTION. HAVE PROJECTION OF 1 INCH. JOB NUMBER T21V0558A ADDRESS

# RELEASE / REVISION DWN / CHK ENG DATE 0 ANCHOR RODS CM / ATS BMO 09/27/2021 1 PERMITS CM / ATS BMO 10/05/2021 2 REV. ANCHOR BOLTS BTW / JMW 11/29/2021 3 Finals BTW / TJF 01/06/2022 AB3 SHEET DRAWING STATUS FOR CONSTRUCTION HAE

01/ 18/ 202 2